★ The first real truck suspension in 130 yearsMade in USAVeteran owned
Commercial & Hotshot

Helper Springs for Towing: Where They Help and Where They Fall Short

Are helper springs for towing right for your truck? See how they work, how they compare with air bags, and why a fixed spring rate cuts both ways.

"If it sags, add more spring." That is the oldest piece of advice in heavy-duty towing, and it is the whole case for helper springs for towing in one line. It isn't wrong. Extra spring does hold a loaded truck higher. But it leaves out the part every owner discovers a week later, when the trailer is parked and the truck is still riding on all that extra spring to the grocery store.

Helper springs are a good tool with a narrow job. Knowing exactly what that job is will tell you whether they belong on your truck.

What counts as a helper spring

"Helper spring" covers several designs that share one idea: add spring rate at the rear axle so the truck resists sag under load. The common types are:

  • Overload leaves mounted above the main leaf pack, which make contact once the axle compresses under weight.
  • Add-a-leaf setups that slip an extra leaf into the existing pack.
  • Coil-style helpers that sit between the leaf pack and the frame.
  • Progressive rubber or foam helpers that replace or work with the bump stop and firm up the more they compress.

Some of these are in contact all the time. Others leave a gap and only start working once the truck has settled a certain amount. That difference matters more than any other detail when you choose one.

How a fixed spring rate behaves

Every passive spring has a rate: the force needed to compress it a given distance. A helper adds rate. With the load on, the combined springs compress less, so the rear sits higher.

The catch is that the rate doesn't know whether a trailer is attached. An always-in-contact helper stiffens the truck all the time, loaded or empty. A gap-style helper preserves the unloaded ride, but the truck has to sag far enough to close the gap before the helper does anything. So you trade one of two things: some of your empty ride, or some of your loaded stance.

That is the same compromise the factory made with your leaf pack. Heavy-duty pickups already leave the factory with rear springs built for their top rated load, and that is the main reason they ride hard with an empty bed. Helpers push that balance further toward the loaded end.

Where helper springs do their best work

Helper springs suit owners whose load stays roughly the same day after day:

  • A slide-in camper that lives in the bed for the season.
  • A service body, toolbox or transfer tank that never comes off.
  • A work truck that pulls the same trailer on most days.

In those cases, a fixed rate isn't a drawback. The truck carries the same weight most of the time, so one setting fits. Helpers also need almost no attention once installed. There is no pressure to set, no lines to check and no compressor to look after.

Where they fall short when you tow

Towing tends to be the opposite of a steady load. The trailer goes on and comes off, tongue and pin weights vary from trip to trip, and the truck spends many of its miles empty.

They can't adjust. A helper gives the same support for a light utility trailer and a loaded fifth wheel. If it's right for one, it's too much or too little for the other.

They reduce sag rather than remove it. With gap-style designs especially, the rear still drops before the helper engages.

They do nothing for damping. Bounce, float and porpoising come from the shocks. More spring with the same shocks can make the rebound livelier, not calmer.

They don't touch sway or wander. Those come from trailer loading, hitch setup, links and steering parts.

They don't change your ratings. GVWR, rear GAWR, payload and towing capacity stay exactly where the manufacturer put them.

Want support that changes when the trailer does? Read how AdaptiveMotion™ deals with heavy hitch loads on hotshot rigs and gooseneck or fifth-wheel trucks.

Helper springs vs air bags

Owners usually end up choosing between these two, so here is how they compare on the points that come up most.

Adjustability. Air bags change support with pressure, so you can set them for each load. Helper springs are fixed. Whatever rate you install is what you live with.

Upkeep. Helper springs need little more than a look during routine service. Air bags need pressure checks before a tow, plus attention to leaks, lines and, on compressor kits, moisture.

Empty ride. Air bags can be let down to a minimum pressure, which brings the ride close to stock if you remember to do it. Contact-style helpers stiffen the empty ride all the time. Gap-style helpers leave it mostly alone.

Uneven loads. Air bags can usually run different pressures side to side. Most helper springs can't compensate for a load that sits off center.

What neither does. Neither controls damping, and neither raises any weight rating.

A simple way to decide: if your load is constant and you want zero routine checks, helpers make sense. If your load changes and you don't mind adjusting, air bags fit better. If it varies and you would rather never touch a valve or gauge, you are describing a different kind of suspension.

Looking at the whole system instead of one spring

Sag is only one symptom. A truck that tows well also needs damping matched to the load, links that keep the axle located, and roll control that keeps the body settled in corners and crosswinds. Adding spring at the rear addresses one of those and can make the others harder to tune.

AdaptiveMotion™ treats those as one problem. It is a closed-loop, fully active system, and its sensing is built into the shocks: each one checks the pavement 1,000 times in a second, and from those checks the controller sets how firm, how high and how level every corner should be, without the driver choosing anything. Settle a trailer onto the hitch and the system pulls the rear back to level on its own, then firms the damping to handle the added mass. Unhitch and the damping softens again, so an empty truck stops paying for a load it is not carrying. Because the truck is not supported on air springs, the routine that comes with bags (pressure checks, leak hunting, draining moisture) simply is not part of owning it.

The hardware is a 4-link system that bolts on at both the front and rear axles, working with the active shocks, and since no two trucks are set up quite alike, it is the authorized upfitter's call how it ties in with your existing springs and axles. PDS rates it at 12,000 lb for each axle, with self-leveling up to 33 degrees. As with every suspension product, the truck's GVWR, GAWR and payload stay where the factory set them. The upfitter mounts it to existing points on the truck, with no cutting or welding, and PDS says a typical install runs 20 to 24 shop hours. Every kit is serialized, so it leaves with you when the truck does, so the money does not stay behind at trade-in.

You can read more on the PDS heavy-duty truck page and in the AdaptiveMotion™ features rundown.

Choosing the right fix for how you tow

Helper springs are honest hardware. They hold up a steady load with almost no upkeep, and for a truck that carries the same weight every day, that can be enough. For a tow rig whose load changes from trip to trip, a fixed rate is always a compromise, and it leaves bounce, sway and the empty ride untouched. Match the fix to how your load actually behaves, weigh the truck on a certified scale, and have any suspension work done by a qualified shop.

Done living with a fixed spring rate? Look over AdaptiveMotion™ options in the shop, then have an authorized Patriot upfitter take care of the install, or talk to the Patriot team about whether your truck qualifies.

Frequently Asked Questions

Do helper springs increase payload?

No. Payload is the truck's GVWR minus its curb weight, and both figures come from the manufacturer. Helper springs only change how the truck sits under weight. Adding them also adds a little curb weight, which slightly reduces the payload you have left.

Will helper springs make my truck ride rough when empty?

Contact-style helpers usually do, because they add spring rate all the time. Gap-style helpers that only engage after the axle compresses tend to leave the empty ride close to stock.

Can I run helper springs and air bags together?

Some owners do, but stacking two spring add-ons rarely fixes the problems that matter most when towing, such as bounce and sway. Have a qualified suspension shop review the whole setup before adding more spring.

How long do helper springs last?

Steel helpers can last for years, but they can sag or crack under repeated overloading, and rubber or foam helpers can harden and split with age and heat. Have them inspected at routine service intervals.

Are helper springs better than shocks for towing?

They solve different problems. Helper springs resist sag. Shocks control how the truck moves after a bump. A truck that sags and bounces needs attention to both, and stronger springs alone often make the bounce worse.

See how it fits your rig
Serialized ownership from day one.
Shop
heavy-duty towinghelper springsload supporttowing suspensiontruck suspension
Patriot Dynamic Systems
Veteran owned and based in Ponderay, Idaho, Patriot Dynamic Systems builds AdaptiveMotion™, the bolt-on active suspension for heavy-duty trucks, backed by a 10-year, 1,000,000-mile warranty.

Join the conversation

Leave a comment

Your email address won't be published. Comments are reviewed before they appear.